Introducing a Multi-sine EIS Method to Increase Measurement Speed and Avoid Accuracy Losses

Editor’s note: This briefing was written in a joint collaboration between Admiral Instruments and Zahner Scientific Instruments. Admiral Instruments will be exhibiting (booth 400) at the 232nd ECS Meeting in National Harbor this fall. See a list of all our exhibitors.

lithium batteries

Image: Multiple stacks of lithium batteries

Problem

Methods combining EIS with charge-discharge cycles are among the most powerful tools available to collect in-situ information about electrochemical systems such as battery cells and stacks. However, accurately measuring the rapidly-changing states of the electrodes, electrolytes, and other non-steady-state materials within battery systems is a challenge.

This issue is particularly troublesome when changes in state occur at timescales even shorter than a single charge-discharge cycle or single EIS frequency sweep. Accurately interpreting results from an EIS measurement requires either making the ill-advised assumption of steady-state conditions throughout the duration of a frequency sweep, or accounting for drift effects by using modeling tools that are often time-consuming or ineffective.

Solution

One proposed solution is combining 1) parallel EIS measurements, 2) automatic drift correction of the measured time dependent signals, 3) time interpolation by series measurements, and 4) application of a data validation algorithm, for example the Z-HIT algorithm, for data post-processing. As opposed to traditional sequential EIS of a battery stack, parallel EIS is a valuable approach that not only saves time, but eliminates the issue of data drift from non-steady-state conditions originating from sequential measurements. This benefit is a consequence of impedance data being collected throughout the entire system at the same time, rather than just one cell at a time.

Precautions must be taken during the data collection phase to limit any instances of drift signals being incorrectly assigned as an actual reaction or response by the cell or stack being measured [1]. Using the Z-HIT algorithm [2], “non causal” spectra from Kramers-Kronig relations can be converted into corrected spectra by interpolation of the spectra series vs. time and by removing residual “non-causal” spectra. The Z-HIT algorithm has the unique ability to reconstruct drift-affected data [3], and is the transform exclusively used within Zahner’s modeling and simulation software.

In cases where multi-sine EIS is used rather than single-sine EIS, mainly to reduce the amount of time required to collect data, conventional multi-sine EIS methods usually experience significant losses of accuracy. However, by using a “weighted harmonics autocorrelation” technique [4], multi-sine EIS can benefit from the same features of automatic drift correction and error detection that are commonly used for single-sine EIS. With this approach, users can enjoy the time-saving advantages of multi-sine EIS without the loss of accuracy when compared to an equivalent single-sine EIS method.


References
[1] C. A. Schiller, F. Richter, E. Gülzow 3, N. Wagner; J. Phys. Chem. Chem. Phys. 3 (2001) 374
[2] Lasia, Andrzej. “Z-HIT Transform.” Electrochemical Impedance Spectroscopy and its Applications. N.p.: Springer, 2014. 299-300. Print.
[3] W. Ehm, R. Kaus, C. A. Schiller, W. Strunz, New Trends in Electrochemical Impedance Spectroscopy and Electrochemical Noise Analysis, ed. F. Mansfeld, F. Huet, O. R. Mattos, Electrochemical Society Inc., Pennington, NJ, 2001, vol. 2000-24, 1
[4] C.-A. Schiller, R. Kaus; Bulgarian Chemical Communications, Volume 41, Number 2 (2009), pp. 192-198

Posted in Guest Post
DISCLAIMER

All content provided in the ECS blog is for informational purposes only. The opinions and interests expressed here do not necessarily represent ECS's positions or views. ECS makes no representation or warranties about this blog or the accuracy or reliability of the blog. In addition, a link to an outside blog or website does not mean that ECS endorses that blog or website or has responsibility for its content or use.

Post Comments

Your email address will not be published. Required fields are marked *